Davey SP601 Series SPAPOWER CONTROLLERS User Manual download pdf

User’s Guide

Models:

SP400P, Q400PAU-10, Q400PAU-15

SP601AU-15, SP601AU-15T

Q601AU-20, SP601AU-20T

Q601AU-30, SP601AU-30T

SP400P & SP601

8 Self-Diagnostic Error Codes

The Spa Power controller has extensive self diagnostic capabilities. In the event of a problem it will indicate an error

number according to the nature of the problem. The error numbers and their meanings are listed below.

Note:When in an error state the alarm can be muted by pushing the AIR/AUX button.

Error 1 (H20) - Prime Failed

This is not necessarily a problem with the controller itself, but indicates that no water is being detected in the heater

housing. Prime failed is a special case in that it can be recovered from by pushing a button.A push of the pump

button will run the pump for 10 seconds to try to get water to the heater.If successful normal operation will resume.

If unsuccessful, Error 1(H20) will be indicated on the display again. With any Error 3-8, spa operation will stop

and not continue until the controller is reset. The controller can only be reset by pushing the UP, DOWN and

PUMP buttons simultaneously. The controller will remain in an error condition even when reset at mains power,

controller will only continue normal operation after the UP, DOWN and PUMP buttons are pushed simultaneously

(see below).

Error 3 - Stuck Button

This error indicates that one of the buttons in the touchpad is stuck or has been held down for more than one minute.

This may be caused by the pool cover pressing on the touchpad or by water getting into the touchpad or by damage

to the touchpad or its cable. Try to reset the spa. If there is still a problem then contact your spa pool supplier.

Error 4 - No Water Sensor

This error indicates a problem with the optical water sensor in the heater. The problem may by caused by the sensor

being disconnected or by damage to the sensor. Try to reset the spa. If there is still a problem then contact your spa

pool supplier.

Error 5 - Overtemperature

This error indicates that the digital temperature sensor in the heater or pool has detected a temperature of 45

C or

more.This may not be a problem with the controller, it may be caused by excessive pump use in hot weather, or

pump failure. Turn off the spa and allow time for the water to cool. If there is still a problem then contact your spa

pool supplier.

Error 6 - Thermal Cut Out Tripped

This error indicates that the safety electromechanical over temperature cut out on the heater has operated. This

is not necessarily a problem with the controller. It may have occurred from an air lock around the element, high

temperatures during shipping, or failure of the pump. This automatic cut out will only reset once the element has

cooled below about 38 C. The unit must then be reset before it will resume operation. Manually push the UP,

DOWN and PUMP buttons simultaneously.

Error 7- Stuck Relay

This error indicates a problem with the heater control circuitry inside the unit. Contact your spa pool supplier.

Error 8 - No Temperature Data

This error indicates a problem with the digital temperature sensor in the heater or pool wall or that both the in

heater and in pool sensors are connected. Check that only one sensor is connected and that it has not become

disconnected or damaged. Try to reset the spa. If there is still a problem then contact your spa pool supplier.

P/N Q916321-3 supersedes P/N Q916321-2

AUSTRALIA

Head Ofce and Manufacturing

6 Lakeview Drive,

Scoresby, Australia 3179

Ph: +61 3 9730 9222

Fax: +61 3 9753 4100

Website: davey.com.au

Customer Service Centre

Ph: 1300 2 DAVEY

(1300 232 839)

Fax: 1300 369 119

E-mail: sales@davey.com.au

Davey Water Products Pty Ltd

Member of the GUD Group

ABN 18 066 327 517

NEW ZEALAND

7 Rockridge Avenue,

Penrose, Auckland 1061

Ph: +64 9 570 9135

Fax: +64 9 527 7654

E-mail:

[email protected]

Website: daveynz.co.nz

Customer Service Centre

Ph: 0800 654 333

REST OF WORLD

6 Lakeview Drive,

Scoresby, Australia 3179

Ph: +61 3 9730 9121

Fax: +61 3 9753 4248

E-mail:

export@davey.com.au

Website: davey.com.au

Quality

ISO 9001

H/O & MFG SCORESBY

Environment

ISO 14001

H/O & MFG SCORESBY

N2401

RoHS

COMPLIANT

1 2 3 4 5 6

Summary of Contents

Page 1 - SP400P & SP601

User’s Guide Models:SP400P, Q400PAU-10, Q400PAU-15 SP601AU-15, SP601AU-15T Q601AU-20, SP601AU-20T Q601AU-30, SP601AU-30TSP400P & SP601 8 Self-Dia

Page 2

Congratulations on choosing the latest Spa Power control system. This controller makes use of the latest technology, including innovative optical and

Page 3 - Spa Water Treatment

6 Auto Sanitising (Filtration) 6.1 No 24hr Circulation Pump Fitted The Spa Power controller automatically maintains the ltration/sanitising of the sp

Page 4 - 1 Touch Pads

5 Light Operation Your spa may have been tted with either of two different LED lights; a Spa Power Coloured Light (SPCL) or a Spa Power Variable Colo

Page 5 - 2 Temperature Control

4 Auxiliary Air Button The Air Button controls anauxiliary air blower. It is used to turn the blower on and off, and select different operating modes

Page 6 - 3 Pump Operation

3.3 Pump 1 (Two speed, no 24HR circulation pump tted) Pump 1 is controlled by just one touch pad button pushing the pump button 4 times cycles its op

Comments to this Manuals

No comments

Davey SP601 Series SPAPOWER CONTROLLERS User Manual

Browse online or download User Manual for Water equipment Davey SP601 Series SPAPOWER CONTROLLERS. Davey SP601 Series SPAPOWER CONTROLLERS User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Water equipment Davey SP601 Series SPAPOWER CONTROLLERS